CODIGOS DE FALLA DI 350

C0000: Main Motor M2 malfunction

The Lock signal remains HIGH for a continuous 1-sec.

period or more while M2 remains energized.

C0010: I/C Motor M1 malfunction The Lock signal remains HIGH for a continuous 1-sec.

period or more while M1 remains energized.

C0045: Fusing Cooling Fan Motor M3 malfunction

The Lock signal remains HIGH or LOW for a continuous

1-sec. period or more while M3 remains energized.

C004C: Ozone Fan Motor M8 malfunction

The Lock signal remains HIGH or LOW for a continuous

1-sec. period or more while M8 remains energized.

C004E: Power Unit Cooling Fan Motor M4

The Lock signal (analog input voltage) remains 0.4V or

less for a continuous 0.5-sec. period or more while M4

remains energized.

C0070: Main Hopper Toner

Replenishing Motor M6 malfunction

· Toner Bottle Home Position Sensor PC10 remains

blocked (L) for a continuous 2-sec. period or more

while M6 remains energized.

· PC10 remains unblocked (H) for a continuous 6-sec.

period or more while M6 remains energized.

C0050: Warming-up failure The temperature of the Fusing Rollers do not reach the

required level even after the lapse of a given period of

time during a warming-up cycle.

· From room temperature to 100°C: Within 65 sec.

· From 100°C to 140°C: Within 25 sec.

· From 140°C to 170°C: Within 20 sec.

· From 170°C to the completion of warming-up: Within 22 sec.

C0510: Abnormally low fusing temperature

· The fusing temperature remains 130°C or less for a

continuous 0.1-sec. period or more during the

standby state or printing.

· The fusing temperature remains 105°C or less for a

continuous 2-min. period or more during the low-temperature

standby state.

C0520: Abnormally high fusing temperature

The fusing temperature remains 230°C or more for a

continuous 0.1-sec. period or more

C0650: Faulty Scanner Home Position Sensor 1 PC12

Start key pressed when the Scanner is at its home position>

· PC12 is not unblocked (H) even when the Scanner moves

10 mm to the left.

· PC12 is not blocked (L) even when the Scanner moves 4

mm to the right after PC12 has been unblocked (H).

Start key pressed when the Scanner is at any position other

than home>

· PC12 is not blocked (L) even when the Scanner moves

469.5 mm to the right.

C0651: Faulty Scanner Home Position Sensor 2 PC13

When the Start key is pressed with a document loaded in the

Document Feed Tray of AF-7, PC13 is not blocked (L) even

when the Scanner moves 463 mm to the left after PC12 has

been unblocked (H).

C0990: LCC Lift-Up Motor EMOT malfunction (PF-106)

] See option service manual.

C0991 Lift 1 ascent motion failure (PF-106)

C0995: LCC Transport Motor HMOT

malfunction (PF-106)

C0999 Lift 2 ascent motion failure (PF-106)

C099D: Communications error (PF-106)

C0B00: Transport Motor M1 drive malfunction

(FN-100/FN-500)

C0B0F: Paper Entrance Switching

Motor M1 drive malfunction

(FN-100/FN-500)

C0B30: CD Aligning Motor M4 drive

malfunction (FN-100/FN-500)

C0B38: Shift Motor M5 drive malfunction

(FN-100/FN-500)

C0B4D: Paper Holding Tray Motor M10

drive malfunction (FN-100/FN-500)

C0B4E: Finisher Tray Motor M8 drive

malfunction (FN-100/FN-500)

C0B50: Stapling Motor drive malfunction

(FN-100/FN-500)

C0BA0: Elevator Motor M9 drive malfunction

(FN-100/FN-500)

C0F32: Faulty ATDC Sensor E1 The value of data read by E1 is faulty. [E1 reading is 7% or

less (3.92V or more) or 19% or more (1.41V or less).]

C0F33: ATDC adjustment failure
· In an F8 (ATDC control voltage automatic adjustment)

operation, the adjustment of ATDC control voltage is not

completed within 1 min. after E1 sampling.

· In an F8 operation, the control voltage falls outside the

range of 5.39V to 8.15V.

C1038: Engine connection error
· The system fails in checking initial engine connection

when Power Switch S1 is turned ON.

· The system succeeded in checking initial connection

when S1 was turned ON; then it fails in rechecking

initial connection through the execution of a

software reset when a communications error occurs

during operation.

C1300: Polygon Motor M10 malfunction

· The Lock signal is not detected for a given period of

time after the resolution has been selected. (The

Lock signal is not, however, detected for 1 sec. after

the start.)

· No Lock signals are detected for the 1-sec. period

which starts 1 sec. after the first Lock.

] First Lock: The first Lock signal following 1 sec. after

the selection of start or half speed.

· The Lock signal is not detected for a continuous 0.5-

sec. period while M10 is in the stabilized turning

state (after a Lock has been detected).

· The Lock signal remains ON for a continuous 5-sec.

period while M10 remains deenergized.

C133A Communications error

(G/A)

———————————————————

C133B: Communications error

(option I/F)

———————————————————

C13C0: I/C initialization failure After failing to blow the imaging cartridge fuse 2 consecutive

times, 3.6V or more is detected and the I/C is

determined to be new.

C13D0: Faulty EEPROM No initial data is written in EEPROM.

C13F0: HSYNC detection failure · The SOS rising edge is not detected even after the

lapse of 0.2 sec. after Polygon Motor M10 has

started and laser output started.

· No SOS rising edges are detected while VIA

remains ON.